Kit containing 2 stainless steel M10 banjo bolts for Brembo brake fittings with copper washers

Supplied with 4 crush washers. Also known as Guzzi ref. 95990033

 2 in stock

95990028-z 95990028 GU95990028 95 99 00 28
 9599 0028 9599.0028 95.99.00.28

Also fits Laverda Jota

Caliper mounting shim, used to precisely centre caliper over brake disc

 2 in stock

 95100332 GU95100332 95 10 03 32
 9510 0332 9510.0332 95.10.03.32

Full throttle cable

1 cable per carb. 1 ball end, 1 thin bullet shaped end. We advise you to measure your existing cable before ordering in case you have a non standard set up.

 2 in stock

 14117500 GU14117500 14 11 75 00
 1411 7500 1411.7500 14.11.75.00

Complete Speedo (odometer) cable

We advise you to measure your existing cable before ordering in case you have a non standard set up.

 2 in stock

12760400-z 12760400 GU12760400 12 76 04 00
 1276 0400 1276.0400 12.76.04.00

6 volt single lead ignition coil for Lucas Rita ignition

Includes coil clamp. HT lead screws into this coil

 2 in stock

HT lead rubber, used where HT lead screws onto plug cap or pushes onto ignition coil

 2 in stock

 14717600 GU14717600 14 71 76 00
 1471 7600 1471.7600 14.71.76.00

Modern solid state electronic regulator for models with Bosch charging system

Bolts to original mounting point but this replacement part is not as tall as the old metal regulator. Also known as Guzzi ref. 17703800. Replaces ELA29704

See our Bosch fault finder page for help diagnosing problems on your Bosch charging system. The original type mechanical regulator is no loger available

 2 in stock

29703800-z 29703800 GU29703800 29 70 38 00
 2970 3800 2970.3800 29.70.38.00

Reconditioned starter motor and solenoid in black and silver finish. Professionally reconditioned and sold with a 12 month guarantee. This is a suitable replacement for Bosch 8 or 9 tooth Guzzi starter motors. See ELA14738 for replacement solenoid.

This may fit Loop frame models with 5 speed gearboxes, you will need to trim a clearance into the battery tray to make room. The clutch cable bracket will prevent fitment on 4 speed models.

This is an exchange only item, we can supply these before receiving your exchange unit subject to a refundable deposit so you can keep your bike on the road. See ELC10737 for the refundable deposit. Send your old starter motor to our registered address. NB In case of starter motor problems do not tap the casing as this will certainly cause it to fail. See SSA08075 for mounting bolts. Do not remove second nut from terminal posts when fitting - this nut is required to hold the terminal in place

 2 in stock

 14730554 GU14730554 14 73 05 54
 1473 0554 1473.0554 14.73.05.54

Rubber cap for oil pressure switch

 2 in stock

 12717600 GU12717600 12 71 76 00
 1271 7600 1271.7600 12.71.76.00

Thick shim washer for valve spring

Used as lower valve spring shim washer

 2 in stock

 13037200 GU13037200 13 03 72 00
 1303 7200 1303.7200 13.03.72.00